[Jul-2021] Aruba Certified Switching Associate (ACSA) V1 HPE6-A72 Exam Practice Dumps
2021 HPE6-A72 Premium Files Test pdf - Free Dumps Collection
NEW QUESTION 48
You need to remote into an AOS-CX switch using SSH in order to update the management IP address for future connections. Unfortunately, you mis-configured the IP address and are now locked out of the switch.
What command could you have issued before making changes that would have recovered the original switch configuration after ten minutes?
- A. checkpoint auto confirm 10
- B. checkpoint rollback 10
- C. boot system secondary 10
- D. checkpoint auto 10
Answer: D
NEW QUESTION 49
Refer to the exhibit.
Traffic is failing between Core-1 and Host-B. IP addressing has correctly been applied, and all interfaces are attached to the vrf GREEN.
Which configuration will correct the issue?
- A. Core-1(config)# ip route 10.1.20.0/24 10.1.1.2 vrf GREEN
Host-B: assign the default-gateway address 10.1.20.1 - B. Core-2(config)# ip route 0.0.0.0/0 10.1.1.1 vrf GREEN
Host-B: assign the default-gateway address 10.1.20.181 - C. Host-B: assign the default-gateway address 10.1.20.181
- D. Core-1(config)# ip route 10.1.20.0/24 10.1.1.2 vrf GREEN
Host-B: assign the default-gateway address 10.1.20.181
Answer: D
NEW QUESTION 50
Refer to the exhibit.
The Aruba 8400 in the exhibit is member 2 of a VSX stack.
Which command will enter the interface sub configuration mode for the port, indicated by the orange square?
- A. 8400(config)# interface 1/7/16
- B. 8400(config)# interface 1/4/15
- C. 8400(config)# interface 2/3/17
- D. 8400(config)# interface 2/4/15
Answer: D
NEW QUESTION 51
Core(config)# user admin password
Core(config)# interface mgmt
Core(config-if-mgmt)# ip static 10.254.16.89/22
Core(config-if-mgmt)# default-gateway 10.254.19.129
Core(config)# ssh server vrf mgmt
Core(config)# https-server vrf mgmt
You are tasked with configuring the Core switch to be managed by NetEdit. Currently, the Core switch is at factory-default settings.
Which two steps are missing? (Choose two.)
- A. Core(config)# https-server rest access-mode read-only
- B. Core(config-if-mgmt)# no shutdown
- C. Core(config-if-mgmt)# no tftp-server
- D. Core(config)# https-server rest access-mode read-write
- E. Core(config-if-mgmt)# enable
Answer: B,D
NEW QUESTION 52
Which command will suppress LLDP messages from egressing on a given port while still allowing LLDP to be enabled on the switch?
- A. switch(config-if)# no lldp receive
- B. switch(config)# no lldp
- C. switch(config-if)# no lldp transmit
- D. switch(config-if)# no lldp interface (port) transmit
Answer: C
NEW QUESTION 53
Which option correctly describes a WAN network?
- A. compute resources that are networked locally over wireless
- B. a group of computer resources that communicates between geographically separate location
- C. a network of devices over long distances but limited to within a single ISP
- D. the connection between two separate buildings in the same campus
Answer: B
NEW QUESTION 54
What command displays information regarding the secondary image installed on an AOS-CX switch?
- A. show images
- B. show version detail
- C. show secondary
- D. show version
Answer: A
NEW QUESTION 55
Refer to the exhibit.
The above scenario shows a packet from the Server destined for the Firewall. Switch-A and Switch-B are bundled as VSF stack. The LAG between the VSF stack and the firewall indicates a hash function to forward the packet on port 2/1/2.
Which statement is true regarding how Switch-A will forward the packet?
- A. Switch-A will encapsulate the packet using GRE to forward to Switch-B in order for the packet to egress on port 2/1/2 per the hash function.
- B. Switch-A will forward the packet along the VSF link to Switch-B so that it will egress on port 2/1/2 per the hash function.
- C. Switch-A will drop the packet. Multi-Chassis lag to multi-chassis lag is not a supported feature of VSF.
- D. Switch-A will forward the packet on port 1/1/2. VSF will override the typical LAG hash function used for the physical interface selection.
Answer: B
NEW QUESTION 56
Refer to the exhibit.
Traffic is failing between Core-1 and Host-B. IP addressing has correctly been applied, and all interfaces are attached to the vrf GREEN.
Which configuration will correct the issue?
- A. Core-1(config)# ip route 10.1.20.0/24 10.1.1.2 vrf GREEN Host-B: assign the default-gateway address 10.1.20.1
- B. Core-2(config)# ip route 0.0.0.0/0 10.1.1.1 vrf GREEN Host-B: assign the default-gateway address 10.1.20.181
- C. Host-B: assign the default-gateway address 10.1.20.181
- D. Core-1(config)# ip route 10.1.20.0/24 10.1.1.2 vrf GREEN Host-B: assign the default-gateway address 10.1.20.181
Answer: D
NEW QUESTION 57
Match the terms to the correct layer of the OSI model.
Answer:
Explanation:
NEW QUESTION 58
Refer to the exhibit.
What command will display the debug l2mac events?
- A. show debug terminal
- B. show module L2MAC
- C. show debug buffer module L2MAC
- D. show debug all
Answer: C
NEW QUESTION 59
Refer to the exhibit.
What is the correct binary conversion of the last two hexadecimal characters of the physical address?
- A. 1001 1111 0101 0011
- B. 1101 1000
- C. 1110 1101
- D. 1000 1101 1110 1101
Answer: C
NEW QUESTION 60
Refer to the exhibit.
Switch-1 is not the root bridge. The ports shown are all the connected pointtopoint interfaces. What Role (hidden by the blue rectangle) will be assigned to the Lag 1 interface?
- A. Backup
- B. Root
- C. Alternate
- D. Designated
Answer: B
NEW QUESTION 61
Which field in the IPv4 header indicates whether the IP packet carries TCP or UDP traffic?
- A. Protocol
- B. Identification
- C. IHL
- D. TTL
Answer: A
NEW QUESTION 62
Match each description to the correct management tool for Aruba AOS-CX.
Answer:
Explanation:
NEW QUESTION 63
Refer to the exhibit.
What commands will successfully enable the SVI for vlan 100 on interface 1/1/1 to produce the results displayed in the command show ip interface brief in the exhibit below?
- A. Access-1(config)# interface 1/1/1
Access-1(config-if)# routing
Access-1(config-if)# interface vlan 100
Access-1(config-if-vlan)# ip address 10.1.1.1/24 - B. Access-1(config)# interface vlan 100
Access-1(config-if-vlan)# ip address 10.1.1.1/24 - C. Access-1(config-if)# vlan 100
Access-1(config-vlan)# ip address 10.1.1.1/24 - D. Access-1(config)# interface 1/1/1
Access-1(config-if)# vlan trunk permit vlan 100
Access-1(config-if)# interface vlan 100
Access-1(config-if-vlan)# ip address static 10.1.1.1/24
Answer: B
NEW QUESTION 64
Match the switching term to the correct definition.
Answer:
Explanation:
NEW QUESTION 65
Refer to the exhibit.
You are in the process of configuring VSF between Access-1 and Access-2. Access-1 has been configured as the VSF Master.
What is a valid configuration for Access-2 to join the VSF stack?
- A. Access-2# configure
Access-2(config)# vsf member 1 Access-2(config)# vsf renumber-to 2 Access-2(vsf-member-1)# link 2 2/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y - B. Access-2# configure
Access-2(config)# vsf member 2 Access-2(vsf-member-1)# link 2 1/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y - C. Access-2# configure
Access-2(config)# vsf member 2 Access-2(vsf-member-1)# link 1 1/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y - D. Access-2# configure
Access-2(config)# vsf member 1 Access-2(vsf-member-1)# link 1 1/1/28 Access-2(vsf-member-1)# exit Access-2(config)# vsf renumber-to 2 This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y
Answer: C
NEW QUESTION 66
Match the terms to the correct layer of the OSI model.
Answer:
Explanation:
NEW QUESTION 67
The section in blue can be ignored.
SW1(config)# interface 1/1/1-1/1/2
SW1(config-if-<1/1/1-1/1/2)# vlan access 2
SW1(config-if-<1/1/1-1/1/2)# exit
SW1(config)# interface 1/1/11-1/1/17
SW1(config-if-<1/1/11-1/1/17)# vlan access 17
SW1(config-if-<1/1/11-1/1/17)# exit
After completing the above commands, what is the expected output of show vlan with no other vlan commanded having been added?
- A.
- B.
- C.
- D.
Answer: C
NEW QUESTION 68
What are the commands to disable SSH and HTTPS services from the default VRF?
- A. Core-1(config)# no ssh server vrf default Core-1(config)# no https-server vrf default
- B. Core-1# no ssh server vrf default Core-1# no https-server vrf default
- C. Core-1(config)# no ssh server Core-1(config)# no https-server
- D. Core-1(config)# no ssh server enable Core-1(config)# no https-server enable
Answer: A
NEW QUESTION 69
Click on the colored box that corresponds with the line that best represents Broadcast traffic flow.
Answer:
Explanation:
NEW QUESTION 70
......
Get ready to pass the HPE6-A72 Exam right now using our Aruba Certified Switching Associate (ACSA) V1 Exam Package: https://www.prepawayete.com/HP/HPE6-A72-practice-exam-dumps.html
A fully updated 2021 HPE6-A72 Exam Dumps exam guide from training expert PrepAwayETE: https://drive.google.com/open?id=1nPlN_dqJg4slLQONKsNiLv5q5YAd_6YH